Dr. Fixit Tape Adhesive
The 2-part epoxy that makes Dr. Fixit Seal Tape actually stick to concrete — engineered for expansion joints that move, weather that won’t cooperate, and substrates that are rarely bone dry.
What is it?
A solvent-free, 2-component (2:1) epoxy adhesive built to bond Dr. Fixit’s Seal Tape series of flexible joint tapes onto concrete, masonry and precast surfaces.
Where is it used?
Expansion joints, construction joints, cracks and precast panel joints on roofs, basements, water-retaining structures and parking decks.
Why use it?
Ordinary mastics fatigue under movement, UV and ponding water; this thixotropic epoxy grips substrate and tape hard enough that failure happens in the concrete, not the bond line.
How is it applied?
Mix Part A (resin) and Part B (hardener) 2:1, trowel a 1-2 mm bed on both flanks of the joint, bed the Seal Tape over a backer rod so its centre stays unbonded, then cap with a second epoxy layer.
About Dr. Fixit Tape Adhesive
Most expansion-joint failures on Indian sites don’t start with the tape, they start with the glue. Dr. Fixit’s Seal Tape is only as good as what holds it to the concrete, and that’s the gap Dr. Fixit Tape Adhesive closes. It’s a 2-part, solvent-free epoxy — white resin and black hardener mixed 2:1 into a uniform grey — formulated specifically as the bonding layer beneath and over Seal Tape at expansion joints, construction joints, cracks and precast panel joints. Pidilite positions it as a systems product: it doesn’t waterproof anything by itself, it’s the adhesive that lets the tape do that job for the joint’s service life.
What earns it a spot on the BOQ over a generic epoxy is the working behaviour. It’s thixotropic, so it stays put on vertical walls and overhead soffits instead of sagging before it cures — a real problem on basement walls where ordinary bonding compounds run. The rated -30°C to +50°C service range and tolerance for damp (not wet) concrete make it workable across most Indian climate zones, provided the substrate is prepared correctly. At Space Arc we spec it alongside Seal Tape for terrace expansion joints, podium and parking-deck movement joints, and precast panel joints where a plain elastomeric sealant would eventually fatigue under thermal cycling.
The technical insight
The number worth knowing is bond strength: greater than 1.5 N/mm², with failure occurring in the concrete, not at the adhesive interface. A properly mixed joint tears the parent concrete apart before the epoxy bond lets go — the point of using a structural epoxy over a bituminous tape adhesive at movement joints. The trade-off is pot life: about 40 minutes at 30°C (ASTM D2471), shorter still on a hot rooftop. That’s why site teams mix small batches rather than a full kit at once.
Where it is used
- Expansion joints in RCC roof slabs, terraces and podium decks
- Construction (cold) joints between staged concrete pours
- Crack treatment where a tape overlay is specified over injection alone
- Precast panel joints in facades and podium structures
- Basement raft and retaining-wall movement joints
- Water-retaining structure joints (STPs, sumps, overhead tanks) with Seal Tape
- Parking deck expansion joints
- Industrial floor joints using a bonded-tape system
Key advantages
- Solvent-free, safer to mix and apply in enclosed basements and tanks
- Thixotropic, non-sag consistency for vertical and overhead work
- Wide -30°C to +50°C service range suits Indian climates
- Bonds damp as well as dry concrete
- Bond strength exceeds the concrete’s own capacity (failure occurs in the substrate)
- Extended ~40-minute pot life at 30°C for positioning tape before it sets
- Colour-coded parts (white + black = grey) give a visual mix-quality check
- Good chemical and abrasion resistance
Limitations & considerations
- Only works as a system with Dr. Fixit Seal Tape — not a general-purpose adhesive or standalone waterproofing product
- Pot life shortens fast in Indian summer heat, so batch size and crew speed matter more than with a typical mastic
- Needs concrete at least 4 weeks old, under 4% moisture, and mechanically abraded — not a same-week-as-pour product
- Strict full-pack 2:1 mixing only; part-mixed packs are explicitly ruled out by the datasheet
- Vulnerable to rain and moving water before initial cure, so needs a reliable dry-weather window
- Requires a trained applicator for the backer-rod-and-masking-tape sequence — not a DIY-friendly product
Selection & best practice
Work in cooler or shaded conditions in peak summer since pot life at 30°C is already ~40 minutes and drops further above that. Abrade the concrete mechanically, confirm moisture content is under 4%, and mix only what the crew can place within the pot life window. Follow the sequence exactly: insert the foam backer rod, mask the joint centre, trowel the base adhesive layer (1-2 mm) on both flanks, remove the centre masking, bed and roller the Seal Tape to expel trapped air, then cap with a second layer once the base coat has taken its initial set. Keep work covered from rain until cure, and never combine leftovers from separate part-packs — always mix a full pack.
Specifications
| Chemistry | 2-part solvent-free epoxy resin & hardener |
| Mixing Ratio (Resin : Hardener) | 2 : 1 (Part A 4 kg : Part B 2 kg per kit) |
| Colour | Part A white, Part B black; mixed = grey |
| Service Temperature | -30°C to +50°C |
| Density, mixed (@27°C) | 1.75 kg/l |
| Pot Life @30°C (ASTM D2471) | ≈ 40 minutes |
| Bond Strength with Concrete | >1.5 N/mm² (failure in concrete) |
| Compressive Strength @7 days (BS 6319 Pt.2) | ≥45 N/mm² |
| Pack Size | Resin (Part A) 4 kg + Hardener (Part B) 2 kg |
Industry use cases
Residential terrace retrofit
Bonding Seal Tape over a leaking terrace expansion joint during pre-monsoon waterproofing.
Basements & below-ground structures
Sealing raft and retaining-wall movement joints where overhead-adjacent work needs a non-sag epoxy.
Water & sanitation infrastructure
Treating construction and expansion joints in STPs, sumps and overhead tanks alongside Seal Tape.
Parking decks & podium structures
Expansion joints on multi-level decks subject to vehicle loading and thermal movement.
Precast construction
Bonding tape across precast panel joints in facades and modular structures for movement accommodation.
Frequently asked questions
Can Dr. Fixit Tape Adhesive be used without the Seal Tape?
How long do I have to work with it once mixed, especially in Indian summer?
Does it bond to damp concrete, or must the surface be bone dry?
How much adhesive do I need to budget per metre of joint?
Does the joint need a primer before the adhesive goes on?
How soon can the joint take water or foot traffic after installation?
How we position Dr. Fixit Tape Adhesive
Dr. Fixit Tape Adhesive is a companion product, specified alongside Dr. Fixit Seal Tape, and on larger Space Arc scopes it often sits next to Crack X Shrinkfree for crack preparation and Pidifin 2K or LW+ where a broader waterproofing coat is also going down. Within the Dr. Fixit range nothing else is formulated to bond the Seal Tape system. Outside it, the closest alternative is Fosroc, though not a direct swap: Fosroc’s movement-joint work leans on PVC and hydrophilic waterstops cast into the pour rather than a surface-bonded tape-and-epoxy system — a different design decision made at drawing stage, not a mid-project substitution. For a general solvent-free structural epoxy, some specifiers look at Fosroc’s Nitobond EP, but it is built for bonding concrete overlays to old substrates, not for anchoring an elastomeric sealing tape, so it isn’t a genuine equivalent here. Once a project commits to a Seal Tape joint detail, this adhesive remains the one engineered to make it work as designed.
Related Waterproofing products
Source Dr. Fixit Tape Adhesive for your project
Authorised distribution, technical advice & professional application across Delhi NCR and Pan-India.