About Sika Sikafloor MultiDur EB-40 AP

Sikafloor MultiDur EB-40 AP is Sika’s answer to a problem every plant engineer knows well: a floor that is smooth enough to clean but grippy enough to walk and drive on when it is wet. It is a multi-layer epoxy system built around a broadcast principle. A pigmented base coat of Sikafloor-264 is pulled out over primed concrete, and while it is still wet, graded quartz sand of 0.4 to 0.8 mm is thrown into it until the surface can absorb no more. Once cured, the excess is swept off and a seal coat of the same resin is squeegeed over the top, wetting out the exposed grains and binding the whole build into a single rigid layer around 4 mm thick. The result is an engineered texture rather than a painted-on finish, which is why the anti-slip character survives years of scrubbing and traffic.

For a distributor audience it helps to be clear about where this sits in the Sika range. The EB-40 AP is a system specification, not a single tin: it draws on Sikafloor-161 as the primer and Sikafloor-264 for both the base and seal coats, with quartz aggregate doing the structural and textural work in between. That makes it a normal-to-medium-heavy-wear floor, well matched to garages, storage halls, beverage and food wet areas, and car-park decks. It is a rigid epoxy at heart, so it earns its place where impact, point loads and cleanability matter more than the thermal-cycling extremes that call for a polyurethane screed.

The technical insight

The slip resistance here is mechanical, not chemical, and that is the whole point. Instead of relying on a fine additive suspended in a coating, the system embeds a dense field of 0.4 to 0.8 mm quartz grains into the resin and only partially drowns them under the seal coat. Each exposed grain becomes a micro-asperity that breaks the water film under a boot or a wheel, so the floor keeps its grip even when standing water would make a smooth epoxy dangerous. The excess broadcast, applied at around 6.0 kg/m2, guarantees full saturation of the base coat so there are no resin-rich smooth patches. Underneath that texture, the cured epoxy delivers roughly 53 N/mm2 compressive strength, about 76 Shore D hardness at seven days and low Taber abrasion loss (near 41 mg), which is what lets the same floor handle pallet trucks and dropped tools without the aggregate popping loose. The seal coat is doing double duty: it locks the quartz down and closes the surface to make the floor effectively liquid-proof and washable.

Where it is used

• Wet-process floors in breweries, dairies, bottling lines and food-processing halls where washdown and standing water are routine
• Storage and assembly halls carrying pallet-truck and forklift traffic
• Maintenance workshops and vehicle service bays exposed to impact and oil
• Loading ramps and dock areas that need grip on inclines
• Multi-storey and underground car-park decks
• Garages and light-industrial production areas with normal to medium-heavy wear
• Packing and dispatch zones where floors are cleaned frequently
• Corridors and circulation routes linking wet and dry areas

Key advantages

• Built-in, hard-wearing anti-slip texture from broadcast quartz rather than a surface additive that wears away
• Strong mechanical performance, with roughly 53 N/mm2 compressive strength and Shore D near 76 for point-load and impact resistance
• Good abrasion resistance (about 41 mg Taber loss) suited to constant wheel and foot traffic
• Sealed, liquid-proof surface that is straightforward to wash down and keep hygienic
• Available in a range of RAL shades for zoning, walkways and safety marking
• Seamless, jointless finish (except at movement joints) with no grout lines to harbour dirt
• Backed by a globally proven Sika system with consistent component quality
• Suits a broad spread of environments, from food wet areas to car parks, simplifying specification

Limitations & considerations

• It is a rigid epoxy, so it is not the right choice for thermal-shock duty such as steam cleaning, hot-water washdown or cold-store cycling, where a PU screed performs better
• The concrete must be sound and dry, with moisture at or below 4% by mass, minimum 25 N/mm2 compressive strength and at least 1.5 N/mm2 pull-off strength
• The broadcast texture, while cleanable, is deliberately profiled and takes more effort to clean than a smooth self-smoothing floor
• Application demands trained applicators and correct timing between coats; the broadcast must go into a still-wet base coat
• Colour and gloss can shift with UV exposure, so it is best kept to interior and covered areas
• Substrate preparation to a suitable profile (mechanical grinding or shot-blasting) is essential and adds to programme time

Selection & best practice

Specifications

Industry use cases

How we position Sika Sikafloor MultiDur EB-40 AP

Within the Sika flooring family, the EB-40 AP is the anti-slip, medium-heavy-wear option; where you want a smoother, thinner finish for clean rooms or light-industrial areas, look at a self-smoothing Sikafloor topping instead, and for lighter-traffic coatings a thin-film roller-applied epoxy will do. Because the system is built on Sikafloor-161 primer and Sikafloor-264 base and seal coats, those components are worth specifying together for consistency. Across our other brands, the closest genuine alternative for the toughest wet-process and food-grade floors is Fosroc’s Nitoflor TF 100 UH polyurethane-hybrid screed, which we stock for cases involving steam, hot water or thermal shock; for a self-smoothing Fosroc epoxy at 2 mm in cleaner areas, Nitoflor SL2000 is the counterpart. Talk to us and we will match the system to your washdown regime and traffic.

Related Industrial Flooring products

View all Industrial Flooring products →