About Asian Paints SmartCare SmartCare AkrylMax Prime

{“name”:”SmartCare AkrylMax Prime”,”slug”:”smartcare-akrylmax-prime”,”brand”:”Asian Paints SmartCare”,”realProduct”:”yes”,”officialSource”:”https://www.asianpaints.com/content/dam/asian_paints/products/product-information-sheets/SC_AkrylMax_New.pdf”,”category”:”sealants-joint-treatment”,”metaTitle”:”SmartCare AkrylMax Prime | Acrylic Sealant | Space Arc”,”metaDescription”:”SmartCare AkrylMax Prime is Asian Paints’ paintable acrylic sealant for door, window and masonry joints, applied pan-Delhi NCR by Space Arc Engineering.”,”heroSubtitle”:”A paintable acrylic sealant that closes the gap between window frames, masonry joints and a clean, crack-free finish.”,”glance”:{“whatIsIt”:”A one-part, water-based acrylic emulsion sealant (product code 6B05) that cures into a soft, plastic-elastic rubber, rated ISO 11600 Class F-7.5P for joint movement.”,”whereUsed”:”Door and window frame perimeters, switch-board and electrical box joints, masonry and brickwork seams, skirting boards, ceiling cornices, and gaps between painted wood, anodised aluminium or concrete elements — interior and exterior.”,”whyUse”:”It stays paintable after curing (a silicone sealant never does), tolerates joint movement up to 7.5%, is non-corrosive on aluminium frames, and is odourless enough to use in occupied rooms.”,”howApplied”:”Gunned from a 280 ml cartridge into clean, dry, sound joints 4-25 mm wide, tooled smooth with a palette knife or wet finger, left to skin over in minutes and cure for 3-4 days, then top-coated with a water-based primer and paint.”},”about”:”On most Delhi NCR sites, the joint where a window frame meets plaster, or where a switch-board sits into a wall, is the detail painters either rush past or fill with whatever sealant happens to be in the toolbox. SmartCare AkrylMax Prime is Asian Paints’ answer to that specific gap: a single-component, acrylic emulsion-based sealant that dries into a flexible rubber rather than a hard, brittle fill. Because it is water-based, it carries none of the acetic-acid smell of a typical bathroom silicone, and — critically for a paint contractor — it takes a water-based topcoat cleanly, so the sealed joint can be painted to match the wall or frame instead of standing out as a grey or clear bead. The official Asian Paints technical data sheet lists a density of 1.58 g/ml, a joint movement capability of 7.5% (ISO 11600 F-7.5P), a working joint width of 4-25 mm, and a full cure of 3-4 days for a 3-5 mm bead depth at 25-27°C. It ships as a 280 ml cartridge, in white only, with roughly 12.8 running metres of coverage on a 4 mm x 6 mm joint, and a shelf life of one year when stored between +5°C and +25°C.\n\nAt Space Arc Engineering we treat AkrylMax Prime as a finishing-trade sealant, not a structural one — it belongs on the painter’s cart alongside Decoprime and Exterior Primer, applied just before the final coats go on. On repaint jobs across Delhi NCR we typically use it to close the hairline gaps that open up around old wooden and metal frames, seal switch-board edges before re-plastering touch-ups, and tidy masonry joints ahead of an exterior repaint cycle. It is not rated, and should never be sold in, for genuine structural expansion joints, continuous water immersion, or wet-area tanking joints — for those we point clients to purpose-built waterproofing or movement-joint systems instead, and we say so plainly rather than stretch this product beyond its data sheet.”,”technicalInsight”:”The ISO 11600 F-7.5P classification is the number worth reading carefully before specifying this product. \”F\” denotes a facade-grade sealant (as opposed to the higher-duty \”G\” glazing class), and \”7.5P\” means it is tested to accommodate joint movement of only 7.5% of the joint width, in the \”plastic\” (non-elastic-recovery) category. That places AkrylMax Prime firmly at the decorator-sealant end of the acrylic range — good for the small seasonal movement around a door frame or a plastered masonry seam, but well short of the 20-25% movement capability that genuine structural or expansion-joint sealants (polyurethane, silicone, or polysulphide) are built to handle. Being an emulsion, it cures by water evaporation rather than a chemical reaction, which is why depth matters: a 3-5 mm bead needs 3-4 days to fully skin through at 25-27°C, and deeper or wider joints near the 25 mm maximum will take longer and are better filled in stages. The one-year shelf life window (+5°C to +25°C) is also tighter than many solvent-based sealants, so site stock should be rotated rather than stored through a full monsoon season.”,”applications”:[“Sealing perimeter joints around wooden and metal door and window frames before painting”,”Filling gaps at switch-board plates, electrical conduit boxes and junction covers”,”Masonry and plastered brickwork joint sealing on interior and exterior walls”,”Skirting board and ceiling cornice joints”,”Sealing joints on anodised aluminium window sections without risk of corrosion”,”Closing gaps between painted wood trims and adjoining wall surfaces”,”Hairline shrinkage cracks in plaster ahead of a repaint cycle”,”Diluted use as a primer coat on highly porous joint substrates before the main sealant application”],”advantages”:[“Fully paintable with water-based topcoats once cured, so the joint disappears into the wall or frame colour”,”Water-based, odourless formulation comfortable to use in occupied interiors”,”Non-corrosive on metallic surfaces such as anodised aluminium, unlike acid-cure silicones”,”Flexible rubber seal accommodates joint movement up to 7.5%”,”Water and UV resistant for exterior durability”,”No added lead, mercury or chromium compounds, and non-flammable — easier to store and handle on site”,”Simple cartridge-and-gun application with no mixing and no mandatory primer on sound substrates”,”Backed by Asian Paints’ pan-India dealer network, with stocking and application support through Space Arc Engineering”],”limitations”:[“Movement capability is capped at 7.5% (ISO 11600 F-7.5P) — not a substitute for PU, silicone or polysulphide sealants on genuine structural or expansion joints”,”Working joint width is narrow, 4-25 mm — not suited to larger gaps or deep cavities”,”Not recommended on PE, PP, Teflon or bituminous surfaces”,”Not for continuous water immersion or permanently wet substrates”,”Full cure takes 3-4 days for a 3-5 mm bead depth, so top-coating has to wait”,”Sold only in white, 280 ml cartridges — colour matching depends entirely on the topcoat, and there is no bulk pack size for large sites”],”bestPractice”:”Start with a clean, dry, sound joint — dust, loose particles, oil and grease all break adhesion, so wipe the substrate down before gunning any sealant. On highly porous surfaces, either dilute AkrylMax Prime for use as a primer coat or, better, prime first with Decoprime (interiors) or Exterior Primer (exteriors), exactly as the Asian Paints data sheet specifies. Cut the cartridge nozzle at a 45-degree angle sized to the joint, and mask both sides of the joint with tape before gunning to keep the bead line neat — it saves far more time than trimming excess afterward. Tool the bead immediately with a palette knife or a wet finger to remove trapped air and give a smooth profile; on butt joints, allow the first pass to skin for at least 6 hours before applying a second coat. Keep application within the 5°C to 45°C window, and on exterior work, plan around the weather — the joint needs roughly five rain-free hours after application to set. Do not top-coat until the full cure period has passed, and prime again with Decoprime or Exterior Primer immediately before painting for the best adhesion and colour uniformity. On multi-unit residential or commercial repaint contracts, Space Arc sequences this as part of the pre-painting scope so sealed joints and primer coats are ready together, avoiding a second mobilisation to site.”,”specs”:[{“property”:”Product code”,”value”:”6B05″},{“property”:”Chemistry / basis”,”value”:”Acrylic emulsion (water-based)”},{“property”:”Density”,”value”:”1.58 g/ml”},{“property”:”Standard compliance”,”value”:”ISO 11600, Class F-7.5P”},{“property”:”Joint movement capability”,”value”:”7.5%”},{“property”:”Working joint width”,”value”:”4-25 mm”},{“property”:”Drying / cure time”,”value”:”3-4 days for 3-5 mm depth at 25-27°C”},{“property”:”Coverage”,”value”:”~12.8 running metres per 280 ml cartridge (4 mm x 6 mm joint)”},{“property”:”Pack size / colour / shelf life”,”value”:”280 ml cartridge, white only, 1 year between +5°C and +25°C”}],”useCases”:[{“sector”:”Residential renovation”,”detail”:”Sealing repainted window and door frame joints in Delhi NCR apartments before the monsoon season”},{“sector”:”New residential construction”,”detail”:”Post-plaster sealing of frame perimeters ahead of final paint coats”},{“sector”:”Commercial interior fit-outs”,”detail”:”Sealing switch-board plates and skirting joints during office or retail fit-out painting”},{“sector”:”Facade repaint and touch-up”,”detail”:”Closing hairline masonry joints and frame gaps ahead of an exterior repaint cycle”},{“sector”:”Institutional / society AMC painting”,”detail”:”Standard joint-sealing step bundled into annual maintenance repaint contracts by Space Arc”}],”faq”:[{“q”:”Can SmartCare AkrylMax Prime be painted over once it cures?”,”a”:”Yes — that is its main advantage over silicone. Once fully cured (3-4 days for a 3-5 mm bead at 25-27°C), it accepts a water-based primer and topcoat, letting the sealed joint blend into the surrounding wall or frame colour.”},{“q”:”Is it suitable for bathroom or wet-area joints?”,”a”:”No. The manufacturer’s data sheet specifically excludes continuous water immersion and permanently wet substrates, so it should not be used for shower, tub or tank-wall joints — a dedicated sanitary silicone or polysulphide sealant is the correct choice there.”},{“q”:”How is it different from a silicone sealant?”,”a”:”AkrylMax Prime is water-based, odourless and paintable, and it will not corrode metal frames the way some acid-cure silicones can. Silicone typically has higher movement capability and better wet-area performance but cannot be painted and often carries a stronger cure odour.”},{“q”:”What size joints can it fill?”,”a”:”The data sheet rates it for joints 4 mm to 25 mm wide. Narrower hairline cracks or wider structural gaps fall outside its tested range and need a different product or joint detail.”},{“q”:”Does it need a primer before application?”,”a”:”Not on sound, standard substrates. On highly porous surfaces the data sheet recommends either a diluted coat of AkrylMax Prime itself as a primer, or priming with Decoprime (interiors) / Exterior Primer (exteriors) before the sealant, and again before top-coating.”},{“q”:”Does Space Arc supply and apply this on site?”,”a”:”Yes. As an authorised Asian Paints SmartCare distributor and applicator, Space Arc Engineering stocks AkrylMax Prime and sequences it into pre-painting and repaint scopes across Delhi NCR, along with the matching Decoprime and Exterior Primer coats.”}],”positioning”:”Within the SmartCare range, AkrylMax Prime sits alongside Decoprime and Exterior Primer as a pre-painting trio — the sealant closes frame and masonry joints, and the primers prepare the surface either side of it for the topcoat, exactly as Asian Paints’ own application steps specify. For projects that also need broader waterproofing rather than joint-level detailing, Space Arc typically pairs it with SmartCare’s roof and wall waterproofing systems and, for wet-area or higher-movement joints outside AkrylMax Prime’s 7.5% rating, a dedicated sanitary or structural sealant. It is worth being direct about where this product does not compete: it is a decorator-grade acrylic sealant for facade and frame joints, not a substitute for the polyurethane, polysulphide or silicone sealants used on genuine structural expansion joints. For that heavier-duty category, specifiers on Space Arc projects more often look to Fosroc’s Nitoseal range — a different chemistry and performance class built for movement well beyond 7.5%, not a like-for-like alternative to AkrylMax Prime but the credible option when the joint itself demands more than a decorator sealant can give.”}

The technical insight

The ISO 11600 F-7.5P classification is the number worth reading carefully before specifying this product. “F” denotes a facade-grade sealant (as opposed to the higher-duty “G” glazing class), and “7.5P” means it is tested to accommodate joint movement of only 7.5% of the joint width, in the “plastic” (non-elastic-recovery) category. That places AkrylMax Prime firmly at the decorator-sealant end of the acrylic range — good for the small seasonal movement around a door frame or a plastered masonry seam, but well short of the 20-25% movement capability that genuine structural or expansion-joint sealants (polyurethane, silicone, or polysulphide) are built to handle. Being an emulsion, it cures by water evaporation rather than a chemical reaction, which is why depth matters: a 3-5 mm bead needs 3-4 days to fully skin through at 25-27°C, and deeper or wider joints near the 25 mm maximum will take longer and are better filled in stages. The one-year shelf life window (+5°C to +25°C) is also tighter than many solvent-based sealants, so site stock should be rotated rather than stored through a full monsoon season.

Where it is used

• Sealing perimeter joints around wooden and metal door and window frames before painting
• Filling gaps at switch-board plates, electrical conduit boxes and junction covers
• Masonry and plastered brickwork joint sealing on interior and exterior walls
• Skirting board and ceiling cornice joints
• Sealing joints on anodised aluminium window sections without risk of corrosion
• Closing gaps between painted wood trims and adjoining wall surfaces
• Hairline shrinkage cracks in plaster ahead of a repaint cycle
• Diluted use as a primer coat on highly porous joint substrates before the main sealant application

Key advantages

• Fully paintable with water-based topcoats once cured, so the joint disappears into the wall or frame colour
• Water-based, odourless formulation comfortable to use in occupied interiors
• Non-corrosive on metallic surfaces such as anodised aluminium, unlike acid-cure silicones
• Flexible rubber seal accommodates joint movement up to 7.5%
• Water and UV resistant for exterior durability
• No added lead, mercury or chromium compounds, and non-flammable — easier to store and handle on site
• Simple cartridge-and-gun application with no mixing and no mandatory primer on sound substrates
• Backed by Asian Paints’ pan-India dealer network, with stocking and application support through Space Arc Engineering

Limitations & considerations

• Movement capability is capped at 7.5% (ISO 11600 F-7.5P) — not a substitute for PU, silicone or polysulphide sealants on genuine structural or expansion joints
• Working joint width is narrow, 4-25 mm — not suited to larger gaps or deep cavities
• Not recommended on PE, PP, Teflon or bituminous surfaces
• Not for continuous water immersion or permanently wet substrates
• Full cure takes 3-4 days for a 3-5 mm bead depth, so top-coating has to wait
• Sold only in white, 280 ml cartridges — colour matching depends entirely on the topcoat, and there is no bulk pack size for large sites

Selection & best practice

Specifications

Industry use cases

How we position Asian Paints SmartCare SmartCare AkrylMax Prime

Within the SmartCare range, AkrylMax Prime sits alongside Decoprime and Exterior Primer as a pre-painting trio — the sealant closes frame and masonry joints, and the primers prepare the surface either side of it for the topcoat, exactly as Asian Paints’ own application steps specify. For projects that also need broader waterproofing rather than joint-level detailing, Space Arc typically pairs it with SmartCare’s roof and wall waterproofing systems and, for wet-area or higher-movement joints outside AkrylMax Prime’s 7.5% rating, a dedicated sanitary or structural sealant. It is worth being direct about where this product does not compete: it is a decorator-grade acrylic sealant for facade and frame joints, not a substitute for the polyurethane, polysulphide or silicone sealants used on genuine structural expansion joints. For that heavier-duty category, specifiers on Space Arc projects more often look to Fosroc’s Nitoseal range — a different chemistry and performance class built for movement well beyond 7.5%, not a like-for-like alternative to AkrylMax Prime but the credible option when the joint itself demands more than a decorator sealant can give.

Related Sealants & Joint Treatment products

View all Sealants & Joint Treatment products →