About Dr. Fixit Repellin WR

Most waterproofing coatings work by building a film on top of a surface — which is exactly the problem when the surface is the finish you’re paying for. Exposed-brick facades, natural-stone porticos, Mangalore-tiled roofs and cut-stone boundary walls all lose their character the moment someone rolls elastomeric paint over them. Dr. Fixit Repellin WR was built for that gap. It’s a clear blend of siloxane and silane polymers carried in a high-boiling-point solvent that soaks into the pores of masonry and concrete instead of sitting on top, lining the capillaries with a hydrophobic layer that water can’t wet. Rain beads and rolls off; the brick, tile or stone underneath stays exactly as it looked the day it was laid.

That penetrating, non-film chemistry also sidesteps a problem film coatings create for themselves in India’s climate: trapped moisture. A painted or membrane-sealed wall with damp masonry behind it tends to blister, peel or push up efflorescence salts as trapped water hunts for a way out. Because Repellin WR blocks liquid water while staying open to vapour, treated walls keep “breathing” — moisture already inside the substrate keeps evaporating outward even as fresh rain is kept out. That matters for older Delhi NCR bungalows with solid masonry, sloped tiled roofs, and heritage or institutional stonework where conservation norms often rule out film coatings outright. Application is cold, by brush or spray, in two coats, with the chemistry doing its work through capillary action rather than surface build-up.

The technical insight

Silane and siloxane are blended deliberately for what each does well. Silane molecules are small enough to penetrate deep into fine-pored, dense substrates like well-cured concrete, but need ambient moisture and alkalinity to hydrolyse and bond. Siloxanes are larger, pre-reacted oligomers that don’t penetrate as deep but bond reliably across a wider range of conditions, including more porous, lower-alkalinity materials like clay brick and natural stone. Combining the two, as Repellin WR does, gives reasonable performance across both dense and porous masonry without needing separate products for each. Once cured, the treated pore walls carry hydrophobic silicone-resin groups that push water’s contact angle past 90°, which is why it beads instead of soaking in — while water vapour molecules, being far smaller, still pass through freely. Because the active chemistry sits inside the pore structure rather than as a surface film, it isn’t degraded by UV the way a pigmented or clear acrylic topcoat would be over years of exposure.

Where it is used

• Exposed/fair-face brickwork facades and jaali walls where the brick finish must stay visible
• Mangalore-tiled and country-tiled sloped roofs, common in coastal-style construction seen across Delhi NCR farmhouses
• Corrugated AC sheet and fibre-cement roofing on factory sheds and warehouses
• Natural stone cladding — sandstone, Kota, granite — on facades, porticos and heritage structures
• Painted or plastered external walls as a breathable pre-treatment ahead of a film-forming coating
• Parapets, chajjas and sunshades prone to rain-driven staining and dampness
• Boundary and compound walls repeatedly repainted due to efflorescence

Key advantages

• Invisible finish — doesn’t change the colour, texture or sheen of brick, stone or tile
• Vapour-permeable — blocks liquid water while letting trapped moisture keep escaping, so it won’t blister or trap efflorescence
• Deep capillary penetration from its low viscosity, so protection sits inside the substrate, not just on top
• UV-stable chemistry that won’t yellow or chalk under harsh Indian sun the way some clear acrylics do over time
• Ready to use straight from the drum — no mixing, thinning or catalysing on site
• Fast turnaround: two coats, brush or spray, 24-hour dry time
• Economical per square metre for large roof and facade areas versus a full recoating system

Limitations & considerations

• Does not bridge cracks or joints — hairline and structural cracks need a filler like Dr. Fixit Crack-X Shrinkfree first, or water will still find its way in through the gap
• Being clear and penetrating, there’s no visual cue for coverage during application — missed patches aren’t obvious until the next rain, so it needs a careful, experienced applicator
• Not a substitute for positive or membrane waterproofing on decks, terraces, or any surface that sees standing water
• Performance depends on substrate porosity and condition — old paint films, algae, or dense trowel-finished concrete reduce how well it penetrates and bonds
• Solvent-based, so it needs ventilation during application and standard fire-safety handling and storage precautions

Selection & best practice

Specifications

Industry use cases

How we position Dr. Fixit Repellin WR

Within the Dr. Fixit range, Repellin WR sits alongside — not instead of — the brand’s film-forming systems. Where Dr. Fixit Raincoat Classic/Select builds a visible elastomeric coat over painted plaster and Dr. Fixit Roofseal or Pidiproof LW+ handle membrane- and admixture-side waterproofing, Repellin WR is the choice when the substrate itself — exposed brick, dressed stone, unglazed tile — has to stay visible. It’s typically paired with Dr. Fixit Crack-X Shrinkfree for crack repair beforehand, since Repellin WR itself doesn’t bridge gaps. Where a project instead needs a silane-siloxane hydrophobic layer built into a full anti-carbonation coating system — say, ahead of Dekguard topcoats on an RCC facade or bridge — rather than as a standalone breathable finish, we point specifiers to Fosroc Nitoprime DG: the same core chemistry, used as a primer within a topcoat system instead of a stand-alone treatment.

Related Waterproofing products

View all Waterproofing products →