About Fosroc Nitoflor FC150 LM

Fosroc Nitoflor FC150 LM is part of Fosroc’s well-established Nitoflor FC150 range of solvent-free, high-performance epoxy resin floor coatings. The base FC150 system is supplied as a pre-weighed, multi-component pack (resin base, hardener and pigmented colour pot) that is mixed on site and applied to prepared concrete to produce a seamless, dense, hard-wearing film. The “LM” suffix identifies a specific factory-formulated variant within this family, sitting alongside related grades such as Nitoflor FC150, FC150-IM and the higher-build FC150-HP / HP-SL options, each tuned for a particular balance of build thickness, flow and service condition. Because each grade shares the core solvent-free epoxy chemistry, FC150 LM carries the same fundamental benefits of the platform: an impervious, hygienic surface that resists a wide range of industrial chemicals, stands up to heavy foot and wheeled traffic, and is easy to clean and maintain. For Indian projects, Space Arc Engineering supplies this product through Fosroc’s local manufacturing and distribution, so the grade, pack format and colour options should always be confirmed against the current India-market technical data sheet at the time of order. As an authorised Fosroc distributor and applicator covering Delhi NCR and Pan-India, Space Arc can match the correct FC150 grade to your floor’s traffic, chemical exposure and downtime constraints, and provide method statements and trained applicators where a turnkey supply-and-apply package is needed.

The technical insight

The FC150 platform is a two-pack (plus colour) cold-cure epoxy: a bisphenol-based epoxy resin cross-linked by an amine hardener to form a dense, thermoset film with strong adhesion to sound, dry concrete. Being solvent-free, it builds film thickness in a single pass without the shrinkage and odour associated with solvent-borne coatings, which is why it is favoured for occupied or poorly ventilated interiors. On the standard FC150, Fosroc’s published mechanical figures are a compressive strength of about 70 N/mm2, flexural strength around 40 N/mm2 and tensile strength near 20 N/mm2 once fully cured, with a typical dry film thickness of roughly 250 microns per coat applied in two coats. The chemistry cures by exothermic reaction, so pot life is finite (on the order of 50 minutes at 20 C for the standard grade) and shortens sharply as temperature rises, which is an important consideration on Indian sites in summer. The practical performance of any epoxy floor is governed at least as much by substrate preparation as by the coating itself: the concrete must be sound, dry (typically below about 5 percent moisture), free of laitance and mechanically abraded or shot-blasted to give a clean, open profile. Because LM-specific film-build, coverage and cure values can differ from the base grade, the controlling numbers for a specification should be taken from the current Nitoflor FC150 LM data sheet rather than assumed from the standard product.

Where it is used

• Production and assembly areas in manufacturing plants
• Engineering workshops and maintenance bays
• Warehousing and light-to-medium traffic storage floors
• Food and beverage facilities including dairies, breweries and soft-drink bottling plants
• Commercial and institutional kitchens
• Showrooms, display areas and internal car parks
• Processing plants, plating shops and dye works requiring chemical resistance

Key advantages

• Solvent-free formulation, so minimal odour during application and suitability for occupied or enclosed interiors
• Hard-wearing, abrasion-resistant film that withstands foot and wheeled traffic
• High resistance to a wide range of industrial chemicals, oils and spillage
• Seamless, impervious, hygienic surface that is easy to clean and disinfect
• Low long-term maintenance cost compared with painted or untreated concrete
• Available in a range of standard colours for zoning, safety marking and aesthetics
• Backed by Fosroc technical support and local Indian manufacturing and distribution

Limitations & considerations

• Not a self-levelling screed; it is a coating and will follow, not correct, an uneven or defective substrate
• Requires thorough mechanical surface preparation (shot-blasting or grinding) and a sound, dry, laitance-free concrete base
• Sensitive to substrate moisture and rising damp, which can cause blistering or loss of adhesion without a suitable damp-proof membrane or epoxy moisture barrier
• Limited pot life that shortens significantly at high ambient temperatures common on Indian sites
• Epoxy films can chalk, yellow or gloss-fade under prolonged direct UV, so it is intended for interior use
• For very heavy point loads, thermal shock or aggressive chemical immersion, a thicker screed or specialist lining system may be more appropriate

Selection & best practice

Specifications

Industry use cases

How we position Fosroc Nitoflor FC150 LM

Nitoflor FC150 LM sits in the mid-to-high range of Fosroc’s industrial epoxy floor-coating line. Within the Fosroc system it is naturally specified alongside Nitoprime 25 as primer, and customers comparing build options should also look at the standard Nitoflor FC150, the FC150-IM grade and the higher-build self-levelling Nitoflor FC150-HP / HP-SL for heavier duty or thicker-film requirements, plus Nitoflor anti-slip grains for slip resistance. Against competitor systems, credible alternatives in the Indian market include Sika’s Sikafloor epoxy coating range (for example Sikafloor-264 / Sikafloor-156 build-ups), MBCC/Master Builders Solutions MasterTop epoxy floor coatings, and STP’s epoxy flooring systems; Dr. Fixit (Pidilite) is strongest in waterproofing and repair and is less of a direct match for heavy-duty industrial epoxy floor coatings, though it competes on lighter-duty coatings. The honest positioning is that FC150 LM is an excellent, well-supported choice for hard-wearing, chemically-resistant interior industrial floors where a coating-grade build is sufficient; for very heavy point loading, thermal shock, chemical immersion or thick self-smoothing screeds, a heavier Fosroc grade or a competitor’s screed system may be the better technical fit. Final grade selection, coverage and cure data must be confirmed against the current Nitoflor FC150 LM India technical data sheet at the time of specification.

Related Industrial Flooring products

View all Industrial Flooring products →