Fosroc Nitoflor FC500T
A textured, slip-resistant solvent-free epoxy floor coating from the Fosroc Nitoflor FC500 family, engineered for hygienic, hard-wearing process floors where wet or greasy conditions demand reliable underfoot grip.
What is it?
Nitoflor FC500T is the textured (slip-resistant) variant of Fosroc’s Nitoflor FC500, a high-build, solvent-free epoxy resin floor coating. Where FC500 gives a smooth self-smoothing finish, the ‘T’ version is laid as a coating into which graded anti-slip aggregate is broadcast and locked in, producing a profiled, grippy surface that is still hygienic and easy to clean.
Where is it used?
Food and beverage processing areas, dairies and breweries, commercial and institutional kitchens, clean rooms, laboratories, hospitals and pharma, plus light-to-medium-duty manufacturing, packing and wash-down zones where floors get wet, greasy or contaminated.
Why use it?
It combines the seamless, dust-free, chemically resistant protection of an epoxy coating with a deliberate surface texture, so it meets slip-resistance expectations for wet-process and walk-on safety without sacrificing cleanability or food-grade, taint-free credentials.
How is it applied?
Applied as a system over a prepared, primed concrete substrate: Nitoprime primer, then FC500 resin and hardener blended with FC500 filler and colour pack, applied by trowel, squeegee or roller, with anti-slip aggregate broadcast into the wet film and (typically) a seal coat to lock the texture.
About Fosroc Nitoflor FC500T
Fosroc Nitoflor FC500T belongs to the Nitoflor FC500 range of solvent-free, high-build epoxy floor coatings — Fosroc’s answer to hygienic industrial and commercial concrete floors that need a tough, seamless, easily cleaned surface. The base product, FC500, is a self-smoothing epoxy that can be laid between roughly 0.25 mm and 1 mm in a single application by trowel, squeegee or roller. The FC500T designation is the textured member of that family: the same proven solvent-free epoxy chemistry, but finished with a profiled, slip-resistant surface rather than a flat self-smoothing one.
The naming follows Fosroc’s established convention across the Nitoflor coatings line, where a ‘T’ suffix marks a textured/slip-resistant version of a smooth base coating (the same relationship seen between Nitoflor FC150 and FC150T). In practice the texture is built using carefully graded anti-slip aggregate — Fosroc’s own Nitoflor Anti-Slip Grains are supplied in Fine, Medium and Coarse grades — broadcast into the wet epoxy and then over-sealed, so the operator can dial the level of grip to suit the area.
As a coating system rather than a single tin, FC500T is typically built up from a Nitoprime primer, the FC500 resin-and-hardener pack blended with FC500 filler and a colour pack, and the anti-slip aggregate. Being solvent-free and taint-free, it is well suited to food-contact and enclosed environments where solvent odour and contamination are unacceptable. It cures to a dense, dust-free, chemically resistant film that withstands foot traffic and light vehicular movement, which is why the FC500 family is specified for food processing areas, clean rooms, laboratories, hospitals and light-duty manufacturing — with FC500T extending that into the wet, greasy and wash-down zones of the same facilities.
For Indian projects, FC500T sits in the practical middle ground of Fosroc’s flooring portfolio: more robust and chemically resistant than a thin roller-applied floor paint, but lighter and more economical than a full high-build screed or self-levelling topping. It is a sensible specification wherever hygiene, chemical splash resistance and slip safety all have to be satisfied on the same floor.
The technical insight
The engineering logic of FC500T is that slip resistance and cleanability pull in opposite directions, and the coating resolves that tension by separating the two jobs. The epoxy binder delivers the impermeable, chemically resistant, hygienic film; the broadcast graded aggregate creates a mechanical micro-profile that gives grip even when the surface is wet or contaminated with oils and fats. Because the texture is built from a controlled aggregate grade rather than left to chance, the specifier can tune aggressiveness — a finer grade for walkways and food-prep zones that still need to be mopped clean, a coarser grade for ramps, loading and heavy wash-down areas. As a high-build, solvent-free epoxy laid in the sub-millimetre-to-1 mm range, FC500T sits above thin floor sealers and paints but below structural screeds, so substrate preparation governs success: the concrete must be sound, dry within Fosroc’s stated moisture limits, mechanically abraded or shot-blasted to an open profile, and primed with Nitoprime before the coat is applied. Get the prime and the moisture control right and the system performs as designed; skip them and even the best epoxy will eventually delaminate. Always confirm the exact mixed coverage, pot life, recoat window and full-cure time against the current region-specific Fosroc Technical Data Sheet, because these depend on temperature, the aggregate loading and the build thickness chosen.
Where it is used
- Food and beverage processing floors where wash-down water, oils and fats create slip hazards
- Commercial, institutional and central kitchens, bakeries, dairies and breweries
- Clean rooms, laboratories, pharmaceutical and hospital areas needing hygienic, grippy floors
- Wet-process areas, bottling and packing lines, and chilled or damp production zones
- Light-to-medium-duty manufacturing, assembly and warehousing aisles with foot and trolley traffic
- Ramps, walkways and step nosings inside industrial and commercial buildings requiring anti-slip safety
- Goods-handling, dispatch and light loading areas subject to spillage
Key advantages
- Slip-resistant textured surface tuned by aggregate grade for safe footing in wet or greasy areas
- Solvent-free and taint-free, suiting food-contact, enclosed and occupied environments
- Seamless, dust-free, hygienic finish that is easy to clean and resists bacterial harbourage
- Good chemical resistance to typical process spillages, cleaning agents and mild splashes
- Hard-wearing with good abrasion resistance under foot and light vehicular traffic
- Available in a range of standard colours for zoning, demarcation and brand identity
- Cost-effective high-build coating that bridges the gap between thin floor paints and full screeds
- Part of a complete, compatible Fosroc system (Nitoprime primer, resin/hardener, filler, colour and anti-slip grains)
Limitations & considerations
- Texture traps dirt more readily than a smooth FC500 finish, so cleaning regimes and the right grade must be matched to the area
- Not a heavy-duty screed; for severe thermal shock, impact or aggressive chemical exposure, thicker Nitoflor screeds or PU systems are more appropriate
- Performance is highly dependent on correct surface preparation, substrate dryness and priming with Nitoprime
- Solvent-free epoxy is sensitive to low temperatures and high humidity during application and cure; site conditions must be controlled
- Limited UV/colour stability typical of epoxies — prolonged sunlight can cause yellowing or chalking, so it is intended for interior use
- As a multi-component broadcast system it requires a trained, experienced applicator for consistent texture and finish
- Exact coverage, pot life and cure figures vary with temperature, build and aggregate loading and must be read from the current Fosroc TDS
Selection & best practice
Specify FC500T only after a realistic appraisal of the floor: confirm the concrete is sound, fully cured and within Fosroc’s moisture limits, then mechanically prepare it (shot-blasting or diamond grinding) to an open profile and remove all laitance, oil and curing compound. Always prime with Nitoprime and respect its overcoat window. Select the anti-slip aggregate grade to match each zone — finer where cleanability dominates, coarser where grip is critical — and broadcast it evenly into the wet film, back-rolling and sealing to lock the texture and control sharpness. Mix only what can be laid within the pot life, maintain substrate and air temperature within the TDS range, and protect the floor from traffic and water until fully cured. Agree the cleaning method and chemicals with the client up front, since a textured floor needs the right brushes and detergents to stay hygienic. For critical or large jobs, request a sample bay and a project-specific method statement, and source genuine Fosroc material through an authorised distributor such as Space Arc Engineering to ensure batch traceability and warranty support.
Specifications
| Product family | Fosroc Nitoflor FC500 range |
| Product type | Textured / slip-resistant variant of FC500 (the ‘T’ designation) |
| Chemistry | Solvent-free, high-build epoxy resin floor coating |
| Base finish (FC500) | Self-smoothing, laid approx. 0.25 mm to 1 mm in a single application |
| FC500T finish | Textured surface created with broadcast graded anti-slip aggregate |
| Application method | Trowel, squeegee or roller; aggregate broadcast into wet film, then seal coat |
| System components | Nitoprime primer + FC500 Resin & Hardener + FC500 Filler + Colour Pack + anti-slip grains |
| Anti-slip grain grades | Fine, Medium and Coarse (Nitoflor Anti-Slip Grains) |
| Colours | Range of standard colours available |
| Typical FC-series coating range | Approx. 100 to 500 microns, light-to-medium duty |
| Substrate | Sound, dry, prepared and primed concrete / cementitious screed |
| Solvent / taint | Solvent-free and taint-free (food-grade suitable) |
| Service environment | Interior industrial and commercial floors |
| Detailed figures (coverage, pot life, cure, strengths) | Refer to current region-specific Fosroc Technical Data Sheet |
Industry use cases
Food & Beverage Processing
Wash-down and wet-process floors in dairies, breweries, bottling plants and meat/poultry units where oils, fats and constant water create slip hazards that a smooth coating cannot safely handle.
Commercial & Institutional Kitchens
Central kitchens, hotel and hospital catering, and food-court back-of-house areas needing a hygienic, grippy, easily sanitised floor that meets food-safety expectations.
Pharmaceuticals & Healthcare
Clean rooms, lab corridors, sterile-prep and hospital wet areas where a seamless, dust-free yet slip-resistant epoxy surface supports both hygiene and staff safety.
Light & Medium Manufacturing
Production aisles, packing lines and assembly bays with foot and trolley traffic, where occasional spillage demands abrasion resistance plus dependable underfoot grip.
Warehousing & Logistics
Dispatch, goods-in and ramp areas inside distribution buildings, using a coarser anti-slip grade on inclines and step nosings for safe movement of staff and light vehicles.
Laboratories & Electronics
R&D and QC labs and light electronics assembly where a clean, chemically resistant, low-dust floor with controlled slip resistance is required.
Frequently asked questions
What is Fosroc Nitoflor FC500T?
How is FC500T different from Nitoflor FC500?
Where should FC500T be used instead of a smooth epoxy floor?
What does the FC500T system include and how is it applied?
What are the coverage, cure time and strength figures?
Is FC500T food-safe and chemically resistant?
Can Space Arc Engineering supply and apply FC500T in Delhi NCR and across India?
How we position Fosroc Nitoflor FC500T
Within the Fosroc Nitoflor flooring range, FC500T is the slip-resistant counterpart to the smooth FC500, and it logically pairs with related Fosroc products: Nitoprime as the primer, Nitoflor Anti-Slip Grains to build and tune the texture, and lighter options such as Nitoflor FC150/FC150T or FC50 where a thinner epoxy will do. Where duty is heavier, Space Arc would steer clients up the range to Nitoflor self-levelling toppings (the SL/TF screed families) or polyurethane-cement systems for thermal shock and aggressive wash-down. Against competitors, FC500T occupies the same niche as Sika’s Sikafloor textured/broadcast epoxy systems, MBCC/Master Builders Solutions (formerly MBS) Mastertop coatings, Dr. Fixit’s Pidicrete/industrial epoxy floor coatings, and STP/Choksey epoxy flooring lines — all credible alternatives that an honest specifier should compare on verified TDS data, lead time and applicator track record. The case for FC500T is the maturity and breadth of the Fosroc Nitoflor ecosystem and the assurance of a single, compatible, warranted system from one manufacturer. As an authorised Fosroc distributor and applicator serving Delhi NCR and pan-India, Space Arc Engineering supplies genuine FC500T with batch traceability and provides project-specific specification, sampling and application support — but we will always recommend confirming the final selection against the current region-specific Fosroc Technical Data Sheet for your exact exposure, traffic and hygiene requirements.
Related Industrial Flooring products
Source Fosroc Nitoflor FC500T for your project
Authorised distribution, technical advice & professional application across Delhi NCR and Pan-India.