About Master Builders Solutions MasterKure 111 WB

{

“name”: “MasterKure 111 WB”,

“slug”: “masterkure-111-wb”,

“brand”: “Master Builders Solutions”,

“realProduct”: “yes”,

“officialSource”: “https://assets.ctfassets.net/ctspkgm1yw3s/2K6eXuJ8m5kOtQbHW8xa1q/00cc01cdaf789f890a01fb12da6f2158/TM_MasterKure_111_WB_2025-03-11_EN.pdf”,

“category”: “concrete-repair-rehabilitation”,

“metaTitle”: “MasterKure 111 WB | Concrete Evaporation Control | Space Arc”,

“metaDescription”: “MasterKure 111 WB is Master Builders Solutions’ water-based evaporation retardant that protects fresh concrete before final curing begins in Delhi NCR heat.”,

“heroSubtitle”: “The interim evaporation shield that keeps fresh concrete workable through Delhi NCR’s harshest pour windows, before final curing takes over.”,

“glance”: {

“whatIsIt”: “MasterKure 111 WB is a water-based wax-emulsion evaporation retardant from Master Builders Solutions, applied straight onto freshly screeded concrete to form a temporary, damp-proof surface film. It is explicitly not a permanent curing membrane.”,

“whereUsed”: “Industrial floor slabs, precast concrete yards, pavement quality concrete (PQC) and large RCC raft or slab pours across Delhi NCR and pan-India sites, particularly during hot, dry, windy or sun-exposed placement windows.”,

“whyUse”: “It cuts surface-moisture evaporation by up to 80% through the first, most crack-prone hours after placement, buying finishing crews real working time and reducing plastic-shrinkage cracking and ‘elephant skin’ before final curing is applied.”,

“howApplied”: “Sprayed undiluted or diluted up to 1:1 at 150 to 200 g/m² onto the wet, shiny concrete surface immediately after screeding. Used purely as a trowelling aid, 1 kg is diluted with 3 to 9 parts water, sufficient for roughly 5 to 12 m² of surface.”

},

“about”: “MasterKure 111 WB sits in a category most site engineers don’t think about until they’ve lost a slab to crazing: interim evaporation protection. It is a bright yellow, water-based emulsion, manufactured by Master Builders Solutions Deutschland GmbH, formulated to sit on the water film of freshly placed concrete and slow the rate at which that surface moisture disappears into hot, dry or windy air. Unlike the membrane-forming curing compounds most contractors are familiar with, MasterKure 111 WB is deliberately temporary. Its own technical data sheet is upfront about this: it is not a substitute for proper final curing by plastic sheeting, ponding, or a dedicated curing membrane such as Master Builders Solutions’ own MasterKure 216 WB. What it does instead is buy time, cutting evaporation by up to roughly 80% during the critical window between screeding and floating or power-trowelling, when a concrete surface is most vulnerable to flash drying and the resulting plastic-shrinkage cracks.\n\nFor Delhi NCR and much of pan-India, that window is exactly where large pours go wrong. Industrial floor slabs poured in May or June heat, PQC stretches finished under direct sun, precast yards running exposed casting beds through Gurugram or Faridabad summers, and even winter pours battling the region’s low ambient humidity all share the same problem: the surface skins over and cracks before the trowel crew can catch up, or before final curing measures can practically be put in place across a large floor plate. MasterKure 111 WB addresses that gap directly, and at Space Arc we typically position it alongside a final-cure product rather than as a stand-alone solution, since that is how the manufacturer itself designed the system to work. Site teams that adopt it correctly report visibly smoother finishing, fewer touch-up passes for surface cracking, and a more forgiving trowelling window on days when concrete would otherwise be setting up faster than the crew can work it.”,

“technicalInsight”: “The chemistry here is simpler, and more purpose-built, than it first appears. MasterKure 111 WB is an aqueous emulsion that spreads across the bleed-water layer on top of freshly placed concrete, forming a thin barrier that suppresses vapour transmission without forming a continuous, adherent film the way a true membrane-forming curing compound does. That distinction matters practically: because the layer stays thin and non-permanent, it doesn’t interfere with the finishing operations that follow, and it doesn’t leave a residue that complicates bonding for a subsequent curing compound, topping, or floor coating. The manufacturer’s own dosage guidance reflects this dual-purpose design. Used neat or diluted up to 1:1 at 150-200 g/m², it functions as an interim curing aid for industrial floor construction, with dilution stretched to 1:3 in cooler, more humid conditions where evaporation pressure is lower. Diluted more aggressively, at 1 kg to 3-9 parts water, the same drum becomes a smoothing and trowelling aid, extending the plasticity of the surface so power-floating can proceed cleanly on precast elements or industrial floor pours. Density (0.99 ± 0.02 g/cm³ at 20°C) and pH (7.3 ± 0.5) sit in line with typical wax-in-water curing aids of this type, and the product’s own documentation is candid that it should not be used on concrete showing strong bleed-water segregation, since the mechanism relies on a stable, uniform surface film.”,

“applications”: [

“Interim evaporation control on industrial floor slabs during screeding and power-trowelling through Delhi NCR’s peak-summer pour windows”,

“Trowelling and finishing aid, diluted, ahead of VDF, VDA and warehouse floor toppings where a long, clean finishing window is critical”,

“Precast concrete element yards (kerbs, pavers, panels, blocks) needing extended surface plasticity before demoulding or finishing operations”,

“Large-area RCC raft and slab pours where wind exposure or direct sun risks flash surface drying before floating can begin”,

“Pavement quality concrete (PQC) and highway/bridge deck pours during the critical pre-finishing window”,

“Basement and podium slabs cast during Delhi’s dry, low-humidity winter mornings when surface drying is faster than expected”,

“Interim surface protection ahead of applying a dedicated long-term curing compound such as MasterKure 216 WB”,

“Screeded mortar toppings and precast panel faces where prolonged surface plasticity improves the quality of the final trowelled finish”

],

“advantages”: [

“Reduces surface-moisture evaporation by up to 80% during the first, most crack-prone hours after placement”,

“Water-based emulsion means low odour and none of the solvent-handling risk of solvent-borne curing aids on a live site”,

“Extends surface plasticity so finishing crews get a genuine working window instead of racing the sun on a large floor pour”,

“Directly reduces plastic-shrinkage cracking and ‘elephant skin’ surface defects on freshly placed concrete”,

“Does not stain or discolour the finished concrete surface”,

“One drum serves two purposes: undiluted or 1:1 as an interim curing aid, or diluted 1:3 to 1:9 as a trowelling aid”,

“Dosage flexes with weather, from 150-200 g/m² in hot, dry conditions to more dilute mixes in cooler, humid weather”,

“Backed by Master Builders Solutions’ global manufacturing standards and a 12-month shelf life under correct, frost-free storage”

],

“limitations”: [

“It is explicitly not a final curing compound; the manufacturer requires it be followed by plastic sheeting, ponding, or a membrane-forming compound such as MasterKure 216 WB”,

“Not recommended for use on concrete surfaces showing strong bleed-water segregation”,

“Frost-sensitive in storage, which mainly affects import transit and cold-season warehousing rather than on-site use in most of India”,

“Being a dilutable emulsion, effectiveness depends on choosing the right dilution for site conditions; over-diluting in Delhi’s peak summer heat under-delivers protection”,

“Adds a distinct process step (and cost) ahead of final curing, which some site teams may see as extra handling versus a single-step curing compound”,

“As a Germany-manufactured import, retail-pack lead times and minimum order quantities can matter more than for locally made curing compounds”

],

“bestPractice”: “Apply MasterKure 111 WB immediately after screeding, onto the still-wet, shiny concrete surface, rather than waiting for any visible drying to begin. In Delhi NCR’s peak summer heat, use it undiluted or at a maximum 1:1 dilution and target 150-200 g/m² coverage; in cooler, more humid conditions, dilutions up to 1:3 are generally sufficient. When using it purely as a trowelling aid on industrial floors or precast elements, dilute roughly 1 kg of product with 3-9 parts water depending on how large an area needs to stay workable. Agitate the container before use since it is an emulsion, and never apply it to concrete surfaces showing heavy bleed-water segregation. Most importantly, treat it as step one, not the whole job: schedule proper final curing, by ponding, wet hessian, plastic sheeting, or a dedicated curing compound like MasterKure 216 WB, once floating or power-trowelling is complete. Store drums off the ground, sealed, and protected from frost; a compromised or frozen drum should not be used.”,

“specs”: [

{ “property”: “Raw material basis”, “value”: “Water-based wax emulsion” },

{ “property”: “Appearance and colour”, “value”: “Bright yellow liquid” },

{ “property”: “Density (at 20°C)”, “value”: “0.99 ± 0.02 g/cm³” },

{ “property”: “pH value (at 20°C)”, “value”: “7.3 ± 0.5” },

{ “property”: “Dosage — interim curing (industrial floors)”, “value”: “150–200 g/m², used undiluted or diluted up to 1:1 (up to 1:3 in cool, humid conditions)” },

{ “property”: “Dosage — trowelling/smoothing aid”, “value”: “1 kg diluted with 3–9 parts water, sufficient for 5–12 m²” },

{ “property”: “Evaporation barrier effect”, “value”: “Up to ~80% reduction during initial critical hours” },

{ “property”: “Shelf life”, “value”: “12 months from production, in frost-free, uncontaminated storage” },

{ “property”: “Pack sizes”, “value”: “20 kg cans, 200 kg drums, 1,000 kg IBC containers” }

],

“useCases”: [

{ “sector”: “Industrial & Warehousing Floors”, “detail”: “A Gurugram warehouse floor contractor pouring large slab bays through May and June heat uses MasterKure 111 WB immediately after screeding to hold the surface open for power-trowelling before switching to a final curing compound.” },

{ “sector”: “Precast Concrete Yards”, “detail”: “A Faridabad precast unit producing kerbs and panels applies a diluted trowelling-aid mix across casting beds so surfaces stay workable long enough for a clean, uniform finish before demoulding.” },

{ “sector”: “PQC & Highway Infrastructure”, “detail”: “A pavement quality concrete crew on an NH stretch uses it as interim protection on exposed lanes during the finishing pass, ahead of standard membrane curing once texturing is complete.” },

{ “sector”: “Basement & Podium Slabs”, “detail”: “A Delhi basement contractor pouring large raft slabs on dry winter mornings applies a lighter dilution to counter unexpectedly fast surface drying caused by low ambient humidity.” },

{ “sector”: “Ready-Mix & Large-Pour RCC Contractors”, “detail”: “A ready-mix applicator managing a big single-day RCC raft pour uses MasterKure 111 WB across sections as they’re screeded, so no part of the slab is left exposed and drying while later sections are still being placed.” }

],

“faq”: [

{ “q”: “Is MasterKure 111 WB a replacement for a curing compound?”, “a”: “No, and the manufacturer is explicit about this. It’s an interim evaporation retardant for the hours between screeding and floating or power-trowelling. Once finishing is complete, the slab still needs proper final curing, by ponding, wet covering, plastic sheeting, or a membrane-forming compound such as MasterKure 216 WB.” },

{ “q”: “What’s the difference between MasterKure 111 WB and MasterKure 216 WB?”, “a”: “MasterKure 111 WB is a temporary, non-membrane evaporation retardant used immediately after screeding to protect the surface before finishing. MasterKure 216 WB (and similar curing compounds) form a longer-lasting membrane applied after finishing to carry the concrete through its full curing period. They’re designed to work in sequence, not as alternatives to each other.” },

{ “q”: “Can this be used on residential slab pours, or only large industrial floors?”, “a”: “The manufacturer’s guidance is written around industrial floor construction and precast elements, but the underlying mechanism, an evaporation retardant, is equally relevant to any exposed slab pour in hot, dry or windy conditions. Space Arc can advise on whether it’s proportionate for a smaller residential pour versus simpler wet-curing methods.” },

{ “q”: “What dilution should we use for Delhi’s summer heat versus winter mornings?”, “a”: “In peak summer heat, use it undiluted or at a maximum 1:1 dilution targeting 150-200 g/m². In cooler, more humid conditions, such as Delhi winter mornings, dilutions up to 1:3 are usually adequate, since evaporation pressure is lower.” },

{ “q”: “Will it affect bonding of a later floor coating, epoxy, or VDF topping?”, “a”: “Because it forms a thin, non-permanent surface layer rather than a continuous membrane, it’s designed not to interfere with subsequent finishing operations. That said, any surface receiving a bonded topping or coating should still be assessed and prepared per the topping manufacturer’s substrate requirements before application.” },

{ “q”: “What pack sizes can Space Arc supply, and is it stocked locally?”, “a”: “MasterKure 111 WB is supplied in 20 kg cans, 200 kg drums, and 1,000 kg IBC containers. As it’s manufactured in Germany, Space Arc recommends confirming lead times for your required pack size and project timeline before finalising a pour schedule.” }

],

“positioning”: “Within the Master Builders Solutions MasterKure range, MasterKure 111 WB is best understood as the interim half of a two-part system, designed to be paired with a true membrane-forming final curing compound such as MasterKure 216 WB rather than used alone. Space Arc typically recommends the pairing for large industrial floor pours and PQC work where the gap between finishing and final curing coverage is otherwise a real risk. For specifiers who prefer a single-step curing solution instead of this two-stage approach, Fosroc’s Concure WB is a genuine alternative worth considering, a water-based wax-emulsion curing membrane that seals moisture into the slab in one application rather than requiring a separate interim and final stage.”,

“fosrocAlternative”: {

“name”: “Concure WB”,

“slug”: “fosroc-concure-wb”,

“note”: “A specifier who wants a single-application, membrane-forming curing compound rather than MasterKure 111 WB’s interim-plus-final two-step approach may prefer Fosroc Concure WB for simpler site logistics on smaller or less time-critical pours.”

}

}

The technical insight

The chemistry here is simpler, and more purpose-built, than it first appears. MasterKure 111 WB is an aqueous emulsion that spreads across the bleed-water layer on top of freshly placed concrete, forming a thin barrier that suppresses vapour transmission without forming a continuous, adherent film the way a true membrane-forming curing compound does. That distinction matters practically: because the layer stays thin and non-permanent, it doesn’t interfere with the finishing operations that follow, and it doesn’t leave a residue that complicates bonding for a subsequent curing compound, topping, or floor coating. The manufacturer’s own dosage guidance reflects this dual-purpose design. Used neat or diluted up to 1:1 at 150-200 g/m², it functions as an interim curing aid for industrial floor construction, with dilution stretched to 1:3 in cooler, more humid conditions where evaporation pressure is lower. Diluted more aggressively, at 1 kg to 3-9 parts water, the same drum becomes a smoothing and trowelling aid, extending the plasticity of the surface so power-floating can proceed cleanly on precast elements or industrial floor pours. Density (0.99 ± 0.02 g/cm³ at 20°C) and pH (7.3 ± 0.5) sit in line with typical wax-in-water curing aids of this type, and the product’s own documentation is candid that it should not be used on concrete showing strong bleed-water segregation, since the mechanism relies on a stable, uniform surface film.

Where it is used

• Interim evaporation control on industrial floor slabs during screeding and power-trowelling through Delhi NCR’s peak-summer pour windows
• Trowelling and finishing aid, diluted, ahead of VDF, VDA and warehouse floor toppings where a long, clean finishing window is critical
• Precast concrete element yards (kerbs, pavers, panels, blocks) needing extended surface plasticity before demoulding or finishing operations
• Large-area RCC raft and slab pours where wind exposure or direct sun risks flash surface drying before floating can begin
• Pavement quality concrete (PQC) and highway/bridge deck pours during the critical pre-finishing window
• Basement and podium slabs cast during Delhi’s dry, low-humidity winter mornings when surface drying is faster than expected
• Interim surface protection ahead of applying a dedicated long-term curing compound such as MasterKure 216 WB
• Screeded mortar toppings and precast panel faces where prolonged surface plasticity improves the quality of the final trowelled finish

Key advantages

• Reduces surface-moisture evaporation by up to 80% during the first, most crack-prone hours after placement
• Water-based emulsion means low odour and none of the solvent-handling risk of solvent-borne curing aids on a live site
• Extends surface plasticity so finishing crews get a genuine working window instead of racing the sun on a large floor pour
• Directly reduces plastic-shrinkage cracking and ‘elephant skin’ surface defects on freshly placed concrete
• Does not stain or discolour the finished concrete surface
• One drum serves two purposes: undiluted or 1:1 as an interim curing aid, or diluted 1:3 to 1:9 as a trowelling aid
• Dosage flexes with weather, from 150-200 g/m² in hot, dry conditions to more dilute mixes in cooler, humid weather
• Backed by Master Builders Solutions’ global manufacturing standards and a 12-month shelf life under correct, frost-free storage

Limitations & considerations

• It is explicitly not a final curing compound; the manufacturer requires it be followed by plastic sheeting, ponding, or a membrane-forming compound such as MasterKure 216 WB
• Not recommended for use on concrete surfaces showing strong bleed-water segregation
• Frost-sensitive in storage, which mainly affects import transit and cold-season warehousing rather than on-site use in most of India
• Being a dilutable emulsion, effectiveness depends on choosing the right dilution for site conditions; over-diluting in Delhi’s peak summer heat under-delivers protection
• Adds a distinct process step (and cost) ahead of final curing, which some site teams may see as extra handling versus a single-step curing compound
• As a Germany-manufactured import, retail-pack lead times and minimum order quantities can matter more than for locally made curing compounds

Selection & best practice

Specifications

Industry use cases

How we position Master Builders Solutions MasterKure 111 WB

Within the Master Builders Solutions MasterKure range, MasterKure 111 WB is best understood as the interim half of a two-part system, designed to be paired with a true membrane-forming final curing compound such as MasterKure 216 WB rather than used alone. Space Arc typically recommends the pairing for large industrial floor pours and PQC work where the gap between finishing and final curing coverage is otherwise a real risk. For specifiers who prefer a single-step curing solution instead of this two-stage approach, Fosroc’s Concure WB is a genuine alternative worth considering, a water-based wax-emulsion curing membrane that seals moisture into the slab in one application rather than requiring a separate interim and final stage.

Related Concrete Repair products

View all Concrete Repair products →