About Fosroc Concure HC

Concrete only reaches its designed strength and durability if the cement is kept moist long enough to hydrate. On real sites – open pavements, sprawling floor slabs, bridge decks baking in the Indian sun – traditional water curing with hessian and ponding is slow, wasteful and hard to keep continuous. Fosroc Concure HC is the practical answer: a resin-based curing compound you spray on once and forget. It lays down a continuous film across the fresh surface that traps the mix water inside the slab, so hydration continues from within instead of the top few millimetres drying out and going weak, dusty and crazed.\n\nConcure HC belongs to Fosroc’s established resin curing-compound family, the same lineage as Concure A. It is supplied ready to use as a single-component liquid, white-pigmented so applicators can see exactly where it has and hasn’t landed, and so the light colour reflects sunlight and holds down the concrete’s peak temperature during the critical first day. Beyond curing, the resin film is hard-wearing and, on many jobs, can double as a primer surface for compatible subsequent finishes – a genuine labour saving compared with clear wax emulsions that must be fully removed before anything is bonded down.

The technical insight

Freshly placed concrete loses water two ways: bleed water evaporating off the top, and the mix water the cement actually needs to react. If the surface dries before hydration is well advanced, the near-surface paste is starved, leaving a soft, permeable, dusting skin over sound concrete below. Concure HC works by forming a physical membrane. As the solvent flashes off, the resin coalesces into a continuous, low-permeability film that dramatically slows evaporation from the surface – the water stays in the slab and drives hydration. The white pigment does a second job: it reflects solar radiation, curbing the temperature rise on exposed pours and reducing the thermal gradient that leads to early-age cracking. Because the compound is applied at a controlled rate in one coat, the film thickness is consistent, which is what governs how well it holds water – the reason Fosroc specifies a coverage band rather than \”as much as you like.\” It is a curing method that trades a bagful of hessian and a week of re-wetting for one calibrated spray pass.

Where it is used

• Curing of concrete road and highway pavements where continuous water curing is impractical
• Airport runway, taxiway and apron slabs exposed to sun and wind
• Bridge deck and viaduct concrete cured against rapid moisture loss
• Large-area industrial and warehouse floor slabs
• Precast concrete elements needing consistent, labour-light curing
• Canal linings, hardstandings and industrial-estate pavements
• Any exposed horizontal pour where the white pigment aids solar reflection and visual coverage checks

Key advantages

• Sprayed on in a single pass – far less labour than ponding, hessian or repeated re-wetting
• Continuous resin film retains mix water so cement hydrates fully and near-surface concrete stays hard, not dusty
• White pigment reflects sunlight, lowering peak concrete temperature and early-age thermal cracking risk
• Pigment also gives an instant visual check that the whole surface has been coated
• Ready to use as supplied – no site mixing or dilution
• Hard-wearing film with good adhesion that can serve as a primer for many compatible finishes
• Reduces surface permeability and shrinkage, improving long-term durability
• Well suited to large open areas and infrastructure where water curing simply cannot be sustained

Limitations & considerations

• Solvent-borne and flammable – needs good ventilation, no ignition sources, and correct fire-safe storage
• Where a fully bonded topping, membrane or coating is required and the resin will not act as an accepted primer, the film must be mechanically removed by grinding, abrasion or hydro-jetting
• Timing is unforgiving: apply after bleed water has gone but before initial set, or coverage and performance suffer
• Must not be exposed to rain or moving water until it has become tack-free
• Coverage and moisture retention depend on an even film at the specified rate – patchy or thin spraying under-cures the slab
• Not a substitute for good concrete practice – it manages surface moisture loss, it does not fix a poor mix or bad placement

Selection & best practice

Specifications

Industry use cases

How we position Fosroc Concure HC

Concure HC is the resin-based, solar-reflective option in Fosroc’s curing range – best where you want a hard-wearing white film that can double as a primer for compatible finishes. If a water-based, non-flammable membrane is preferred – for enclosed areas, lower odour, or simpler handling – Fosroc Concure WB (a white wax emulsion) is the natural alternative from the same family, though wax films must be removed before bonded toppings. For jobs that then move on to floor coatings or repairs, Space Arc pairs curing with the wider Fosroc system: Nitoflor industrial floor toppings, Nitobond bonding agents, Renderoc repair mortars and Nitoproof/Brushbond waterproofing. Where a project standardises on another brand, we also supply comparable curing compounds from MC-Bauchemie and Dr. Fixit – talk to our technical team about matching the compound to the downstream finish.

Related Concrete Admixtures products

View all Concrete Admixtures products →