About UltraTech Tilefixo Ultima Plus

{“name”:”UltraTech Tilefixo Ultima Plus”,”slug”:”ultratech-tilefixo-ultima-plus”,”brand”:”UltraTech”,”realProduct”:”yes”,”officialSource”:”https://www.ultratechcement.com/tilefixo/product/ultima-plus”,”category”:”tile-fixing”,”metaTitle”:”UltraTech Tilefixo Ultima Plus | Highly Flexible | Space Arc”,”metaDescription”:”UltraTech Tilefixo Ultima Plus is a highly deformable, weather-resistant adhesive for exterior tile cladding. Supplied by Space Arc, Delhi NCR & Pan-India.”,”heroSubtitle”:”UltraTech’s highly deformable, weather-resistant tile adhesive, purpose-built for exterior wall cladding and vibration-prone facades.”,”glance”:{“whatIsIt”:”A single-component, cement-based, polymer-modified tile adhesive from UltraTech’s TileFixo range, formulated for high flexibility (deformability) rather than plain static bond strength.”,”whereUsed”:”Exterior wall and facade cladding, balconies, terraces, boundary walls and any substrate exposed to thermal movement, wind load or structural vibration — typically with large-format vitrified, porcelain or natural-stone tiles.”,”whyUse”:”Its ‘highly deformable’ formulation absorbs the expansion-contraction cycling that Delhi NCR’s hot summers and monsoons put on exterior tile work, reducing the hollow-sounding, cracked or de-bonded tiles that plague ordinary rigid adhesives on facades.”,”howApplied”:”Mixed with clean water to a lump-free, gel-consistency paste, combed onto the prepared substrate with a notched trowel sized to the tile, then the tile is pressed and slid perpendicular to the ridges to close air voids — back-buttering is recommended for large-format or vertical stone.”},”about”:”UltraTech’s TileFixo range is built as a tiered system rather than one all-purpose adhesive, and Ultima Plus sits at the flexible end of that ladder. Sumo CT and Royal NT below it cover ordinary ceramic and natural-stone floor and wall work; Ultima Plus is reserved for the harder job of holding tile and stone onto exterior walls, where sun-heated masonry expands by day and contracts by night, where nearby traffic or machinery sets up low-level vibration, and where a standard rigid adhesive eventually shears at the tile-substrate interface. UltraTech markets the base Ultima as ‘deformable’ and Ultima Plus as ‘highly deformable’ — in adhesive-industry terms, a step further up the flexibility ladder, engineered specifically for facades and movement-prone substrates rather than for raw pull-off strength on a static floor.\n\nFor a Delhi NCR facade contractor, that distinction has a direct site consequence: drummy (hollow-sounding) tiles and edge-lipping on exterior cladding are almost always symptoms of the adhesive not keeping pace with thermal movement, not of poor tiling technique. Specifying Ultima Plus on elevations, balcony parapets, boundary walls and any wall panel near expansion joints removes that variable up front instead of it turning into a warranty callback later. Space Arc Engineering stocks it as an authorised UltraTech distributor and applicator across Delhi NCR and pan-India, and can pair the adhesive selection with the correct notch-trowel sizing, joint width and grout (TileFixo Style Epoxy or CG Grout) for the tile format on a given project.”,”technicalInsight”:”The word that matters on the datasheet is ‘deformable’. Within the IS 15477:2019 and EN 12004:2017 / ISO 13007-1:2014 tile-adhesive framework, ordinary cementitious adhesives are classed C1 or C2 purely on bond strength; adhesives that must also flex with the substrate carry an added S-suffix — S1 for deformable, S2 for highly deformable. UltraTech’s own product language for Ultima (‘deformable’) and Ultima Plus (‘highly deformable’) maps onto that S1/S2 distinction, which is the technical reason Ultima Plus — not Royal NT, a straight C2TE Type-3T adhesive with no deformability claim — is the right call for an exterior cladding elevation. The non-slump gel consistency matters too: a paste that doesn’t sag under its own weight is what keeps a freshly set course of tiles from sliding on a tall facade before the adhesive skins over.”,”applications”:[“Exterior wall and facade tile/stone cladding on RCC or block masonry”,”High-rise elevation cladding subject to daily thermal expansion-contraction cycling”,”Balcony parapets, terraces and boundary walls exposed to weathering”,”Tiling near structural expansion joints and vibration sources (roads, rail corridors, machinery)”,”Large-format vitrified, porcelain and natural-stone tile fixing on vertical exterior surfaces”,”Tile-on-tile re-cladding of old, sound exterior surfaces after proper substrate preparation”,”Podium and compound-wall tile cladding on commercial and institutional buildings”,”Facade repair work where existing tiling has failed from rigid-adhesive debonding”],”advantages”:[“Highly deformable formulation absorbs thermal and vibration movement instead of transferring stress straight to the tile-adhesive bond line”,”Non-slump gel consistency holds tiles in place on vertical facades without slip before set”,”Extended open time gives more workable minutes before skinning — useful in Delhi’s hot, dry site conditions”,”No-hollowness bonding reduces the drummy, hollow-sounding tiles common on exterior work”,”Weather-resistant once cured, suited to monsoon-exposed elevations”,”Single-component powder — no separate polymer liquid to dose and mix on site”,”Backed by UltraTech’s Building Products technical service plus Space Arc’s own site support”,”Part of a tiered TileFixo system, so one brand covers interior floors through to demanding facades without switching manufacturers”],”limitations”:[“A cementitious adhesive, not a substitute for a properly detailed movement/expansion joint — it manages ordinary thermal flex, it does not bridge a structural gap”,”Not suited to flexible, metal, glass, plastic or polyurethane-membrane substrates, or to interior floors where a standard Sumo/Royal-tier adhesive is more cost-effective”,”Pot life, open time and cure all shorten in Delhi’s peak summer heat and wind, so batching and application speed need to be managed on site”,”Bond performance depends on a sound, laitance-free, primed substrate — surface prep quality matters as much as the adhesive itself”,”Being a premium flexible-grade adhesive, it costs more per bag than a standard Type-1/Type-2 product, so it’s worth reserving for cladding and movement-prone work”,”Exact dosage, coverage and cure figures for this specific SKU aren’t published on UltraTech’s product page — confirm against the current pack/TDS with Space Arc before finalising a BOQ”],”bestPractice”:”Prepare the substrate first — remove oil, dust, laitance and any old paint or polish, and lightly dampen dry masonry before troweling. Mix only what can be used within the pot life, using a mechanical stirrer for a lump-free gel, and let it slake for a couple of minutes before a final mix. Comb the adhesive with a notch trowel matched to the tile size, and for large-format tiles or vertical natural stone, back-butter the tile as well as combing the wall to avoid trapped air pockets. Work within the stated open time — re-comb any skinned adhesive rather than laying over it — and tile bottom-to-top on vertical elevations. Provide proper movement joints at the intervals recommended for exterior tiling rather than relying on adhesive flexibility alone, and leave the installation undisturbed for the full cure period before grouting or loading.”,”specs”:[{“property”:”Chemistry / System”,”value”:”Cement-based, polymer-modified tile & stone adhesive (single-component powder + water)”},{“property”:”Deformability Class”,”value”:”Highly deformable / high-flex grade — positioned as the S2-tier flexible option in the range”},{“property”:”Recommended Use”,”value”:”External wall tile & stone cladding and vibration-prone / thermal-movement substrates”},{“property”:”Consistency”,”value”:”Non-slump gel consistency for vertical and overhead application”},{“property”:”Key Performance Traits”,”value”:”No-hollowness bonding, extended open time, weather-resistant, high flexibility”},{“property”:”Product Family / Variants”,”value”:”UltraTech TileFixo Ultima series — Ultima, Ultima Plus, Ultima White”},{“property”:”Reference Framework (TileFixo range)”,”value”:”Formulated to the IS 15477:2019 & EN 12004:2017 / ISO 13007-1:2014 tile-adhesive standards”},{“property”:”Standard Pack Size (TileFixo cementitious range)”,”value”:”20 kg bag”},{“property”:”Companion Grout”,”value”:”UltraTech TileFixo Style Epoxy Grout or CG Grout for joint filling”}],”useCases”:[{“sector”:”Residential High-Rise Facades”,”detail”:”Vitrified and porcelain tile cladding on tower elevations where daily heat cycling and wind load stress the bond line.”},{“sector”:”Commercial & Retail Elevations”,”detail”:”Storefront and building-facade stone/tile cladding needing a clean, hollow-free finish that survives years of weathering.”},{“sector”:”Facade Renovation & Re-cladding”,”detail”:”Replacing failed rigid-adhesive exterior tiling with a deformable system to stop repeat debonding.”},{“sector”:”Boundary Walls & Compound Cladding”,”detail”:”Tile-clad boundary and compound walls near roads or gates, where passing traffic sets up low-level vibration.”},{“sector”:”Balconies & Terraces”,”detail”:”Open-to-sky tiled surfaces that see the sharpest daily temperature swings and monsoon wetting-drying cycles.”}],”faq”:[{“q”:”How is Tilefixo Ultima Plus different from Tilefixo Royal NT?”,”a”:”Royal NT is a strong, standard C2TE (Type 3T) adhesive for interior and general exterior floor/wall tiling. Ultima Plus is the ‘highly deformable’ member of the range, built for exterior cladding and vibration-prone substrates where the bond has to flex with thermal movement, not just pass a pull-off test.”},{“q”:”Can I use Ultima Plus for interior floor tiling?”,”a”:”You can, but it’s over-specified and costlier for that job — Sumo CT/Sumo CT Plus or Royal NT will handle interior floors and walls at a lower cost. Save Ultima Plus for exterior cladding and movement-prone locations where its flexibility earns its price.”},{“q”:”What tile sizes and materials does it suit?”,”a”:”It’s positioned for large-format vitrified, porcelain and natural-stone tiles on exterior walls, though it also handles smaller-format exterior cladding. Confirm the notch-trowel size against your tile’s back-groove requirement.”},{“q”:”Does it come in a white or light shade?”,”a”:”Yes — UltraTech also sells Tilefixo Ultima White in the same performance tier, useful where adhesive shadowing through light natural stone is a concern.”},{“q”:”What should I grout with after using Ultima Plus?”,”a”:”UltraTech recommends its own TileFixo Style Epoxy Grout or CG Grout for the best system compatibility on the completed cladding.”},{“q”:”Can Space Arc supply and support this on a Delhi NCR facade project?”,”a”:”Yes — Space Arc Engineering is an authorised UltraTech distributor and applicator across Delhi NCR and pan-India, and can help confirm dosage, coverage and notch-trowel sizing against the current TDS before you order.”}],”positioning”:”Within UltraTech’s own TileFixo family, Ultima Plus is the flexible-cladding specialist: Sumo CT and Sumo CT Plus handle everyday ceramic tile work, Aqua Marine VT and VT Plus cover vitrified tiles and wet/submerged areas, Royal NT / Royal NT Plus / Royal NT White handle medium-to-large format tiles and natural stone on general floors and walls, and the Ultima trio (Ultima, Ultima Plus, Ultima White) is reserved for exterior cladding and vibration-prone substrates — Ultima Plus being the highly-deformable option, Ultima White its light-shade counterpart. Outside UltraTech, the closest comparable products are the S1/S2-class flexible tile adhesives from Weber, MYK Laticrete and Bal, which compete on the same deformability positioning for facade work. Fosroc, despite being a genuine alternative brand for Space Arc’s waterproofing, grouting and concrete-repair lines, does not carry a directly comparable tile-adhesive product — for the expansion-joint detailing that typically accompanies a tiled facade, Fosroc’s sealant range is a relevant complementary, not competing, system to specify alongside Ultima Plus.”}

The technical insight

The word that matters on the datasheet is ‘deformable’. Within the IS 15477:2019 and EN 12004:2017 / ISO 13007-1:2014 tile-adhesive framework, ordinary cementitious adhesives are classed C1 or C2 purely on bond strength; adhesives that must also flex with the substrate carry an added S-suffix — S1 for deformable, S2 for highly deformable. UltraTech’s own product language for Ultima (‘deformable’) and Ultima Plus (‘highly deformable’) maps onto that S1/S2 distinction, which is the technical reason Ultima Plus — not Royal NT, a straight C2TE Type-3T adhesive with no deformability claim — is the right call for an exterior cladding elevation. The non-slump gel consistency matters too: a paste that doesn’t sag under its own weight is what keeps a freshly set course of tiles from sliding on a tall facade before the adhesive skins over.

Where it is used

• Exterior wall and facade tile/stone cladding on RCC or block masonry
• High-rise elevation cladding subject to daily thermal expansion-contraction cycling
• Balcony parapets, terraces and boundary walls exposed to weathering
• Tiling near structural expansion joints and vibration sources (roads, rail corridors, machinery)
• Large-format vitrified, porcelain and natural-stone tile fixing on vertical exterior surfaces
• Tile-on-tile re-cladding of old, sound exterior surfaces after proper substrate preparation
• Podium and compound-wall tile cladding on commercial and institutional buildings
• Facade repair work where existing tiling has failed from rigid-adhesive debonding

Key advantages

• Highly deformable formulation absorbs thermal and vibration movement instead of transferring stress straight to the tile-adhesive bond line
• Non-slump gel consistency holds tiles in place on vertical facades without slip before set
• Extended open time gives more workable minutes before skinning — useful in Delhi’s hot, dry site conditions
• No-hollowness bonding reduces the drummy, hollow-sounding tiles common on exterior work
• Weather-resistant once cured, suited to monsoon-exposed elevations
• Single-component powder — no separate polymer liquid to dose and mix on site
• Backed by UltraTech’s Building Products technical service plus Space Arc’s own site support
• Part of a tiered TileFixo system, so one brand covers interior floors through to demanding facades without switching manufacturers

Limitations & considerations

• A cementitious adhesive, not a substitute for a properly detailed movement/expansion joint — it manages ordinary thermal flex, it does not bridge a structural gap
• Not suited to flexible, metal, glass, plastic or polyurethane-membrane substrates, or to interior floors where a standard Sumo/Royal-tier adhesive is more cost-effective
• Pot life, open time and cure all shorten in Delhi’s peak summer heat and wind, so batching and application speed need to be managed on site
• Bond performance depends on a sound, laitance-free, primed substrate — surface prep quality matters as much as the adhesive itself
• Being a premium flexible-grade adhesive, it costs more per bag than a standard Type-1/Type-2 product, so it’s worth reserving for cladding and movement-prone work
• Exact dosage, coverage and cure figures for this specific SKU aren’t published on UltraTech’s product page — confirm against the current pack/TDS with Space Arc before finalising a BOQ

Selection & best practice

Specifications

Industry use cases

How we position UltraTech Tilefixo Ultima Plus

Within UltraTech’s own TileFixo family, Ultima Plus is the flexible-cladding specialist: Sumo CT and Sumo CT Plus handle everyday ceramic tile work, Aqua Marine VT and VT Plus cover vitrified tiles and wet/submerged areas, Royal NT / Royal NT Plus / Royal NT White handle medium-to-large format tiles and natural stone on general floors and walls, and the Ultima trio (Ultima, Ultima Plus, Ultima White) is reserved for exterior cladding and vibration-prone substrates — Ultima Plus being the highly-deformable option, Ultima White its light-shade counterpart. Outside UltraTech, the closest comparable products are the S1/S2-class flexible tile adhesives from Weber, MYK Laticrete and Bal, which compete on the same deformability positioning for facade work. Fosroc, despite being a genuine alternative brand for Space Arc’s waterproofing, grouting and concrete-repair lines, does not carry a directly comparable tile-adhesive product — for the expansion-joint detailing that typically accompanies a tiled facade, Fosroc’s sealant range is a relevant complementary, not competing, system to specify alongside Ultima Plus.

Related Tile Fixing products

View all Tile Fixing products →