Dr. Fixit Curing Compound
White-pigmented wax-emulsion curing compound that forms a moisture-sealing film on fresh concrete and reflects solar heat.
Dr. Fixit Curing Compound at a glance
The essentials specifiers and contractors ask first — answered straight from the product data, with links to go deeper.
What is it?
Dr. Fixit Curing Compound is a water-based, white-pigmented wax-emulsion liquid that you brush or spray onto freshly placed concrete. It dries to a continuous membrane that seals the surface and holds the mix water inside the concrete through the critical early hydration period, while its white pigment reflects sunlight and heat to keep the slab cooler.
Where is it used?
Use it on concrete roads, pavements and highways, industrial and warehouse floor slabs, terrace and roof slabs, precast elements, bridge decks, canal linings, and vertical faces such as retaining walls and basement walls as soon as the shuttering is struck.
Why use it?
It prevents premature evaporation of mix water so cement hydration runs to completion, which means higher strength and far less plastic-shrinkage cracking; the reflective white film also keeps the concrete cool and at a more uniform temperature, reducing thermal cracking. One application replaces several days of manual ponding or hessian re-wetting.
How is it applied?
Apply it by brush or spray as one continuous film. On a fresh horizontal surface, apply once the bleed water has gone and final trowelling is over; on in-situ vertical concrete, apply as soon as the shuttering is removed. The film breaks down by natural weathering over time, but the manufacturer requires you to clean off all film traces before plaster or any subsequent coating.
Key advantages
- Retains the concrete's own mix water so hydration completes, giving higher in-place strength and a denser, less dusty surface
- White pigment reflects solar light and heat, keeping the slab cooler and at a more uniform temperature, which reduces thermal and surface cracking
- Markedly reduces plastic-shrinkage cracking on large flatwork by slowing early evaporation
- Single-coat, labour-saving application by brush or spray replaces days of ponding, hessian or continuous water curing
- Saves water on site, which is valuable on remote, high-rise or water-scarce projects
- Curing efficiency passes ASTM C309-89, with 98 percent daylight reflectance against the standard MgO block
- Water-based, so it is low-odour and easy to clean tools with water before it dries
- Suited to a wide range of structures, from roads and floors to bridge decks, precast and vertical faces
Specifications
- Type: Water-based, white-pigmented wax emulsion; membrane-forming curing compound
- Appearance: Milky white free-flowing liquid
- Curing efficiency: Passes ASTM C309-89
- Daylight reflectance: 98% vs standard MgO block (ASTM C309-89)
- Theoretical coverage: 3 to 5 m2 per litre, depending on surface texture and porosity
- Specific gravity: 1.0 to 1.2
- Solid content: 38 to 42%
- pH: 7 to 8
- Surface drying time: Maximum 60 minutes
- Application method: Brush or spray
- Packaging: 30 litre
- Shelf life: 24 months
Related products
Explore complementary systems and the wider range:
About Dr. Fixit Curing Compound
A plain-language overview of what Dr. Fixit Curing Compound is, the problem it solves and how Space Arc Engineering positions it in a specification.
Curing is the step on a concrete job that is most often shortchanged, yet it decides whether the in-place concrete reaches the strength and durability the mix was designed for. Cement needs water to hydrate; if the surface water evaporates before hydration is complete, the top layer stays weak, dusty and prone to shrinkage cracks. Dr. Fixit Curing Compound addresses this by sealing the freshly finished surface with a thin membrane so the concrete cures using its own mix water, with no ponding bunds, no hessian, and no continuous water supply on site.
It is a water-based wax emulsion that is pigmented white. The wax is what forms the moisture-retaining film once the water carrier flashes off; the white pigment is a deliberate second function, reflecting the sun's light and heat so the slab runs cooler and at a more even temperature. That matters in Indian site conditions, where high ambient temperatures, direct sun and drying wind are exactly the factors that cause rapid moisture loss and early-age cracking. The compound is a milky white free-flowing liquid that dries to a continuous film.
Space Arc supplies Dr. Fixit Curing Compound and advises specifiers and site teams on where membrane curing is the right call, how to dose it for the surface texture in front of them, and how to sequence it with the rest of the finishing trade so the curing film and the later finishes both perform. Because it is a curing aid and not a waterproofing coating, we are clear with clients about what it does and does not replace on the project.
The technical insight
Why Dr. Fixit Curing Compound behaves the way it does — the mechanism behind the performance, in specifier-friendly terms.
The compound works by film formation, not by chemically reacting with the concrete. When the liquid is applied to fresh concrete, the water carrier evaporates and the wax particles coalesce into a continuous, low-permeability membrane over the surface. That membrane sharply slows the rate at which the concrete's own pore water can escape, so the relative humidity at and just below the surface stays high and cement hydration continues for the days it needs rather than being cut short by evaporation. The result is a denser, harder, more abrasion-resistant surface zone and a much lower risk of plastic-shrinkage cracking. The membrane is graded by ASTM C309-89, and the manufacturer's data sheet reports that curing efficiency to ASTM C309-89 passes, with a daylight reflectance of 98 percent measured against the standard magnesium-oxide block.
Where Dr. Fixit Curing Compound is used
Typical applications Dr. Fixit Curing Compound is specified for, supplied by Space Arc Engineering across Delhi NCR, Ghaziabad, Noida and Uttar Pradesh.
- Concrete roads, pavements and highways — large-area film applied immediately after finishing and texturing
- Industrial and warehouse floor slabs — applied after power-floating to stop surface drying and dusting
- Terrace and roof slabs — applied once the slab is finished to retain mix water through early hydration
- Precast concrete elements — panels, beams and columns cured in the precast yard without ponding
- Bridge decks and flyover slabs — applied after surface texturing on large exposed pours
- Canal linings, dams and irrigation structures — membrane curing of extensive water-retaining concrete
- Tall structures such as chimneys and cooling towers — curing where water curing is impractical
- Retaining walls and basement faces — applied to vertical in-situ concrete as soon as shuttering is struck
Key advantages
The properties that make Dr. Fixit Curing Compound the right choice — drawn from the manufacturer's product literature.
- Retains the concrete's own mix water so hydration completes, giving higher in-place strength and a denser, less dusty surface
- White pigment reflects solar light and heat, keeping the slab cooler and at a more uniform temperature, which reduces thermal and surface cracking
- Markedly reduces plastic-shrinkage cracking on large flatwork by slowing early evaporation
- Single-coat, labour-saving application by brush or spray replaces days of ponding, hessian or continuous water curing
- Saves water on site, which is valuable on remote, high-rise or water-scarce projects
- Curing efficiency passes ASTM C309-89, with 98 percent daylight reflectance against the standard MgO block
- Water-based, so it is low-odour and easy to clean tools with water before it dries
- Suited to a wide range of structures, from roads and floors to bridge decks, precast and vertical faces
Limitations & considerations
Where Dr. Fixit Curing Compound is not the right answer. Check these constraints from the manufacturer before specifying — using it outside its scope is the most common cause of failure.
- It is a curing compound, not a waterproofing or protective coating; it does not seal the concrete against water ingress, chemicals or long-term wear and must not be specified for those duties
- Although the film weathers away over time, the data sheet requires the surface to be thoroughly cleaned of all film traces before plaster, tiling or any subsequent coating, otherwise adhesion of those finishes can be compromised — do not assume a no-removal finish
- Timing is unforgiving: applied while bleed water is still present the film is diluted and can flake; applied too late, after the surface has dried, much of the benefit is lost
- Being white-pigmented it leaves a visible film, so it is not suited where the bare finished concrete must stay clean or decorative without further treatment
- It is an aid to good curing practice, not a cure for a poor mix, poor placement or inadequate finishing
Selection & best practice
How to decide whether Dr. Fixit Curing Compound fits your job — and how to apply it so the repair lasts.
Specify a membrane curing compound like Dr. Fixit Curing Compound where conventional water curing is impractical or unreliable — large-area flatwork such as roads, runways and industrial floors, sloped or vertical faces that cannot be ponded, precast yards, and remote or high-rise sites where a continuous water supply is hard to maintain. The white-pigmented grade is the right choice when the pour is exposed to strong sun and the reflective, heat-reducing benefit is wanted. Where the concrete will receive plaster, tiles or a bonded coating later, plan for the cleaning step the data sheet requires, or weigh conventional water curing instead; and never use a curing compound in place of a true waterproofing system.
Application best practice
- Confirm the surface is ready: on horizontal pours apply only after the bleed water has disappeared and final trowelling is over; on in-situ vertical concrete apply as soon as the shuttering is struck
- Apply a single, continuous, uniform film by brush or spray, following the finishing team closely so no area is left exposed to dry out
- Increase the spread rate on rough, textured or porous surfaces, which consume more material than smooth floated finishes
- Stir the material before use so the wax emulsion and pigment are uniformly distributed
- Protect the freshly applied film from rain, traffic and mechanical damage until it has dried
- Before any plaster, tiling or coating, clean the surface thoroughly to remove all traces of the cured film so the subsequent finish bonds properly
Specifications
Indicative properties from the manufacturer's literature. Always confirm batch-specific values against the current TDS before specification.
| Type | Water-based, white-pigmented wax emulsion; membrane-forming curing compound |
|---|---|
| Appearance | Milky white free-flowing liquid |
| Curing efficiency | Passes ASTM C309-89 |
| Daylight reflectance | 98% vs standard MgO block (ASTM C309-89) |
| Theoretical coverage | 3 to 5 m2 per litre, depending on surface texture and porosity |
| Specific gravity | 1.0 to 1.2 |
| Solid content | 38 to 42% |
| pH | 7 to 8 |
| Surface drying time | Maximum 60 minutes |
| Application method | Brush or spray |
| Packaging | 30 litre |
| Shelf life | 24 months |
Coverage, dosage, pack sizes and cure times vary with substrate and conditions — request the full TDS for certified technical data.
Industry use cases
Real-world scenarios where Dr. Fixit Curing Compound is the practical choice — the teams who reach for it and the jobs it does for them.
- Highway and expressway construction, where kilometres of pavement-quality concrete must be cured uniformly without a continuous water supply along the alignment
- Industrial and logistics flooring, where a dense, hard, low-shrinkage wearing surface is critical to floor durability and flatness
- Precast manufacturing, where consistent curing in the yard supports predictable strength gain and faster, repeatable production cycles
- Bridge, flyover and infrastructure decks, where large exposed pours in hot, windy conditions are highly vulnerable to early-age cracking
- Water-resources works such as canals and reservoirs, where extensive concrete faces need reliable curing across large areas
Frequently asked questions
Common questions about specifying and sourcing Dr. Fixit Curing Compound.
Is Dr. Fixit Curing Compound a waterproofing product?
No. Despite sometimes being listed alongside waterproofing products, it is a concrete curing compound, classified by the manufacturer as a concrete admixture. Its job is to retain the mix water so the concrete cures properly and to reflect heat; it is not a barrier against water ingress, chemicals or wear. If you need waterproofing, a dedicated membrane or coating system is required in addition to good curing.
When should it be applied?
On a fresh horizontal surface, apply it once the bleed water has disappeared and final trowelling is complete. On in-situ vertical concrete, apply it as soon as the shuttering is removed. Applying while bleed water is still present dilutes and disrupts the film; applying after the surface has dried out loses much of the curing benefit, so the application crew should follow the finishing team closely.
How is it applied, and at what coverage?
Apply it by brush or spray as a single, continuous, uniform film. The theoretical coverage is about 3 to 5 square metres per litre depending on the surface — rough, textured or porous surfaces consume more than smooth floated finishes, so plan a higher spread rate for those. It is supplied in 30 litre packs.
Does the film need to be removed before plastering or coating?
Yes, take this seriously. While the film does break down by natural weathering over time, the manufacturer's data sheet specifically instructs that the surface be cleaned thoroughly to remove all traces of the film before plaster or any subsequent application, so that those finishes bond properly. Do not assume the film simply disappears and leaves a ready-to-coat surface.
What standard does it meet?
The manufacturer's data sheet states that its curing efficiency passes ASTM C309-89, with a daylight reflectance of 98 percent measured against the standard magnesium-oxide block. We list only what the official data sheet states; if you need the product evaluated against a specific Indian Standard for your specification, ask us and we will confirm with the manufacturer rather than assume compliance.
Why is the compound white?
The white pigment is a functional feature, not just colour. It reflects sunlight and heat off the fresh concrete, keeping the slab cooler and at a more uniform temperature, which reduces surface and thermal cracking. This is particularly useful on large exposed pours under strong sun.
Can it replace water curing entirely?
On many large or hard-to-water structures it is the practical curing method and saves both water and labour. But it is an aid to good curing, not a substitute for sound concrete practice. On critical elements, or where the surface will be heavily loaded or coated, your engineer may still specify or supplement with conventional curing; we are happy to advise on the right approach for your pour.
References
Manufacturer and technical sources this page draws on. Always confirm current data against the live TDS before specification.
Source Dr. Fixit Curing Compound for your project
Space Arc Engineering is an authorised distributor for Dr. Fixit, serving Delhi NCR, Ghaziabad, Noida and Uttar Pradesh. Talk to us for pricing, the technical data sheet and on-site support.
Or email info@space-arc.com · www.space-arc.com